Differences

This shows you the differences between two versions of the page.

--- rtorrent [2009/05/10 01:29] – jt
+++ rtorrent [2020/08/10 02:35] (current) – external edit 127.0.0.1
@@ Line 18: / Line 18: @@
     * + or - : changes the download priority of selected torrent.
     * Backspace : adds the specified .torrent. After pressing this button write full path or URL of .torrent file. You can use Tab and other tricks from bash.
 Main View Keys
+=== Peer list View Keys ===
+Use Arrow Key to navigate on related torrent.
+    * *     : Snub peer (stop uploading to this peer)
+    * k     : Kick peer (disconnect from peer)
+    * B     : Ban peer (No unbanning is possible.) 0.8.4+
+=== Tracker list View Keys ===
+    * left   : Switch to view selection
+    * *      : Enable/disable tracker
+    * space  : Rotate trackers in a group
 ==== Stop torrents after reaching a specified upload ratio ====
@@ Line 139: / Line 154: @@
 schedule = throttle_2,05:00:00,24:00:00,download_rate=25
 </code>
+==== Secure Torrent from ISP Capping ====
+Not 100% but following you two steps avoid capping from ISP,\\
+== Encryption ==
+according to manual you can encrypt your transfer and request encryption only\\
+If Encryptiong is successfully enabled you can avoid ISP to capping on packets. which make you partially secure.
+Enable following line in your .rtorrent.rc
+<code bash | .rtorrent.rc>
+encryption=allow_incoming,try_outgoing,require,enable_retry,require_RC4
+</code>
+== Random Ports ==
+This will change ports on every "restart" of the rtorrent.\\
+port_range specify any high number port range - many be bigger than 11K.\\
+Also enable random port.
+<code bash | .rtorrent.rc>
+port_range = 12000-12999
+port_random = yes
+</code>
 ==== Saving torrent state and resume data between sessions ====
@@ Line 188: / Line 227: @@
 ==== rTorrent Profile ====
+This is the current profile that I am using for my rtorrent client. Though most is using the defaults, there are some decent features.
+<code bash | .rtorrent.rc>
+# This is an example resource file for rTorrent. Copy to
+# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
+# uncomment the options you wish to enable.
+safe_sync = yes
+# Maximum and minimum number of peers to connect to per torrent.
+#min_peers = 40
+#max_peers = 100
+# Same as above but for seeding completed torrents (-1 = same as downloading)
+#min_peers_seed = 10
+#max_peers_seed = 50
+# Maximum number of simultanious uploads per torrent.
+#max_uploads = 15
+# Global upload and download rate in KiB. "0" for unlimited.
+download_rate = 2000
+upload_rate = 750
+# Default directory to save the downloaded torrents.
+directory = /media/harddisk3/home/jason/images2
+# Default session directory. Make sure you don't run multiple instance
+# of rtorrent using the same session directory. Perhaps using a
+# relative path?
+session = ~/rsession
+# Watch a directory for new torrents, and stop those that have been
+# deleted.
+schedule = watch_directory,5,5,load_start=/media/harddisk3/home/jason/images2/*.torrent
+#schedule = untied_directory,5,5,stop_untied=
+# Close torrents when diskspace is low.
+schedule = low_diskspace,5,60,close_low_diskspace=100M
+# Stop torrents when reaching upload ratio in percent,
+# when also reaching total upload in bytes, or when
+# reaching final upload ratio in percent.
+# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
+#schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"
+# The ip address reported to the tracker.
+#ip = 127.0.0.1
+#ip = rakshasa.no
+# The ip address the listening socket and outgoing connections is
+# bound to.
+#bind = 127.0.0.1
+#bind = rakshasa.no
+# Port range to use for listening.
+#port_range = 6890-6999
+# Start opening ports at a random position within the port range.
+#port_random = no
+# Check hash for finished torrents. Might be usefull until the bug is
+# fixed that causes lack of diskspace not to be properly reported.
+#check_hash = no
+# Set whetever the client should try to connect to UDP trackers.
+use_udp_trackers = yes
+# Alternative calls to bind and ip that should handle dynamic ip's.
+#schedule = ip_tick,0,1800,ip=rakshasa
+#schedule = bind_tick,0,1800,bind=rakshasa
+# Encryption options, set to none (default) or any combination of the following:
+# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
+#
+# The example value allows incoming encrypted connections, starts unencrypted
+# outgoing connections but retries with encryption if they fail, preferring
+# plaintext to RC4 encryption after the encrypted handshake
+#
+# encryption = allow_incoming,enable_retry,prefer_plaintext
+# Enable DHT support for trackerless torrents or when all trackers are down.
+# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
+# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
+# The default is "off". For DHT to work, a session directory must be defined.
+#
+#dht = off
+# UDP port to use for DHT.
+#
+# dht_port = 6881
+# Enable peer exchange (for torrents not marked private)
+#
+# peer_exchange = yes
+#
+# Do not modify the following parameters unless you know what you're doing.
+#
+# Hash read-ahead controls how many MB to request the kernel to read
+# ahead. If the value is too low the disk may not be fully utilized,
+# while if too high the kernel might not be able to keep the read
+# pages in memory thus end up trashing.
+#hash_read_ahead = 10
+# Interval between attempts to check the hash, in milliseconds.
+#hash_interval = 100
+# Number of attempts to check the hash while using the mincore status,
+# before forcing. Overworked systems might need lower values to get a
+# decent hash checking rate.
+#hash_max_tries = 10
+</code>