zfs
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
zfs [2016/05/09 19:10] k2patel [Nexenta] |
zfs [2020/08/10 02:35] (current) |
||
|---|---|---|---|
| Line 4: | Line 4: | ||
| - | To check zpool status | + | === To check zpool status === |
| <code bash> | <code bash> | ||
| zpool status [<volume>] | zpool status [<volume>] | ||
| </code> | </code> | ||
| - | To clear error on drive, which you think reported wrongly. | + | === To clear error on drive, which you think reported wrongly. === |
| <code bash> | <code bash> | ||
| zpool clear <volume name> | zpool clear <volume name> | ||
| </code> | </code> | ||
| - | To add Zeus Drive | + | === To add Zeus Drive === |
| <code bash> | <code bash> | ||
| zpool add performance log <drive> | zpool add performance log <drive> | ||
| </code> | </code> | ||
| - | Adding spare to volume | + | === Adding spare to volume === |
| <code bash> | <code bash> | ||
| zpool add performance spare <drive> | zpool add performance spare <drive> | ||
| </code> | </code> | ||
| - | Remove attached spare drive to volume | + | === Remove attached spare drive to volume === |
| <code bash> | <code bash> | ||
| zpool detach <volume> <Drive> | zpool detach <volume> <Drive> | ||
| </code> | </code> | ||
| - | Removing drives from volume (require to remove spare drives after raid rebuilt) | + | === Removing drives from volume (require to remove spare drives after raid rebuilt) === |
| <code bash> | <code bash> | ||
| zpool remove <Volume> <Drive> | zpool remove <Volume> <Drive> | ||
| + | </code> | ||
| + | |||
| + | === List all devices / drive === | ||
| + | |||
| + | <code bash> | ||
| + | sas2ircu 0 DISPLAY | ||
| + | </code> | ||
| + | |||
| + | === ZFS Display drive information by serial number === | ||
| + | |||
| + | <code bash> | ||
| + | sas2ircu 0 DISPLAY | grep -B 9 -A 4 <Serial Number> | ||
| + | </code> | ||
| + | |||
| + | === Freenas Blink Drives === | ||
| + | |||
| + | <code bash> | ||
| + | sas2ircu 0 locate 3:7 ON | ||
| + | </code> | ||
| + | |||
| + | === Offline Drive === | ||
| + | |||
| + | <code bash> | ||
| + | zpool offline hermes 15935140517898495532 | ||
| + | </code> | ||
| + | |||
| + | === Replace disk in ZFS Pool === | ||
| + | |||
| + | <code bash> | ||
| + | zpool replace hermes 15935140517898495532 /dev/disk/by-id/ata-ST3500320AS_9QM03ATQ | ||
| </code> | </code> | ||
| Line 35: | Line 65: | ||
| show lun c8t5000C5005785138Bd0 blink -y | show lun c8t5000C5005785138Bd0 blink -y | ||
| </code> | </code> | ||
| + | === Nexenta Mgmt. === | ||
| + | To create nexenta collector report, Run following command from root prompt | ||
| + | <code bash> | ||
| + | nexenta-collector --no-upload | ||
| + | </code> | ||
| + | Printing Each JBOD Slotmap | ||
| + | <code bash> | ||
| + | nmc -c "show jbod jbod:1 slotmap" | less | ||
| + | </code> | ||
| + | Check HA Status from command line | ||
| + | <code bash> | ||
| + | /opt/HAC/RSF-1/bin/rsfcli status | ||
| + | </code> | ||
| + | Synchronize Disk Location | ||
| + | <code bash> | ||
| + | nmc -c "lunsync -r -y" | ||
| + | </code> | ||
| + | Migrate Pool to another server | ||
| + | <code bash> | ||
| + | /opt/HAC/RSF-1/bin/rsfcli -i0 move <volume> <hostname> | ||
| + | </code> | ||
| ==== Solaris ==== | ==== Solaris ==== | ||
| Line 62: | Line 113: | ||
| devfsadm -Cv | devfsadm -Cv | ||
| </code> | </code> | ||
| + | |||
| + | ==== Check status of ARC and L2 ==== | ||
| + | <code bash> | ||
| + | kstat -p zfs:0:arcstats | ||
| + | </code> | ||
| + | |||
| + | |||
zfs.1462821006.txt.gz ยท Last modified: 2020/08/10 02:29 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
